Enhancing Properties of Metakaolin-Based Geopolymers: The Effect of Zirconia and Silica Nanosphere Additions

Editorial Board PCSS Journal; Mevy Firdaus; Andrie Harmaji; Eva Febrina; Imelda Ruth; Bambang Sunendar; Ibnu Suryatmojo

doi:10.15330/pcss.27.1.35-43

Authors

Mevy Firdaus Faculty of Dentistry, Maranatha Christian University, Bandung, Indonesia; Advanced Materials Processing Laboratory, Institut Teknologi Bandung, Bandung, Indonesia
Andrie Harmaji Advanced Materials Processing Laboratory, Institut Teknologi Bandung, Bandung, Indonesia
Eva Febrina Advanced Materials Processing Laboratory, Institut Teknologi Bandung, Bandung, Indonesia
Imelda Ruth Faculty of Dentistry, Maranatha Christian University, Bandung, Indonesia; Advanced Materials Processing Laboratory, Institut Teknologi Bandung, Bandung, Indonesia
Bambang Sunendar Advanced Materials Processing Laboratory, Institut Teknologi Bandung, Bandung, Indonesia
Ibnu Suryatmojo Faculty of Dentistry, Maranatha Christian University, Bandung, Indonesia

DOI:

https://doi.org/10.15330/pcss.27.1.35-43

Keywords:

geopolymer, zirconia, silica nanospheres, sol-gel, diametral tensile strength, morphology

Abstract

Geopolymers are known for its high compressive but low tensile strength due to its brittle nature, which restricts the use of geopolymers as structural material. It is important to enhance their mechanical performance by incorporating reinforcing materials. This research examines the contribution of silica nanospheres and zirconia to enhance the tensile strength of geopolymer composites utilizing metakaolin. Geopolymers were prepared from an 8M NaOH and sodium silicate activator, which was prepared for 24 hours prior to mixing in a ratio of 2:1. Confirmation of the amorphous silica presence, monoclinic and tetragonal zirconia, and crystalline phases in metakaolin including quartz, mullite, and hematite was verified using X-ray diffraction (XRD) analysis. The scanning electron microscope (SEM) showed that both silica nanospheres and zirconia resulted in a more densely packed microcomposite material with less porosity. Diametral tensile strength (DTS) at 28 days was seen to improve from 2.24 MPa (control) to 2.58 MPa with 80% silica and 3.61 MPa with 60% zirconia and 20% silica nanospheres. These improvements showed that nanomaterials such as silica can enhance the densification of the matrix while zirconia contributes structural reinforcement for improved mechanical properties. The findings here are consistent with earlier work that demonstrated the synergistic effects of silica nanospheres and zirconia to improve geopolymers performance. Findings from this study further demonstrates modified geopolymers can be used in applications requiring high mechanical strength but would require additional investigation to determine its durability and thermal properties to use them in structural and functional applications.

References

M. Amran, et al., Long-term durability properties of geopolymer concrete: An in-depth review. Case Studies in Construction Materials, 15, e00661 (2021); https://doi.org/10.1016/j.cscm.2021.e00661.

K. Chen, et al., Geopolymer concrete durability subjected to aggressive environments – A review of influence factors and comparison with ordinary Portland cement. Construction and Building Materials, 279, 122496 (2021); https://doi.org/10.1016/j.conbuildmat.2021.122496.

A. Harmaji, M.C. Kirana, and R. Jafari, Machine Learning to Predict Workability and Compressive Strength of Low- and High-Calcium Fly Ash–Based Geopolymers. Crystals, 14(10), 830 (2024); https://doi.org/10.3390/cryst14100830.

V. Puspasari, et al., Geopolymer for medical application: a review. Physics and Chemistry of Solid State, 25(3), 626 (2024); https://doi.org/10.15330/pcss.25.3.626-638.

T. Wang, et al., The Influence of Fiber on the Mechanical Properties of Geopolymer Concrete: A Review. Polymers, 15(4), 827 (2023); https://doi.org/10.3390/polym15040827.

L. Qin, et al., Mechanical properties and durability of fiber reinforced geopolymer composites: A review on recent progress. Engineering Reports, 5(12), e12708 (2023); https://doi.org/10.1002/eng2.12708.

H.U. Ahmed, A.A. Mohammed, and A.S. Mohammed, The role of nanomaterials in geopolymer concrete composites: A state-of-the-art review. Journal of Building Engineering, 49, 104062 (2022); https://doi.org/10.1016/j.jobe.2022.104062.

M. Pozzi, et al., Visualization of the High Surface-to-Volume Ratio of Nanomaterials and Its Consequences. Journal of Chemical Education, 101(8), 3146 (2024); https://doi.org/10.1021/acs.jchemed.4c00089.

I. Khan, K. Saeed, and I. Khan, Nanoparticles: Properties, applications and toxicities. Arabian Journal of Chemistry, 12(7), 908 (2019); https://doi.org/10.1016/j.arabjc.2017.05.011.

B.D. Dejak, et al., Evaluation of Hardness and Wear of Conventional and Transparent Zirconia Ceramics, Feldspathic Ceramic, Glaze, and Enamel. Materials, 17(14), 3518 (2024); https://doi.org/10.3390/ma17143518.

J. Li, et al., Understanding of surface chemistry of silica-based nanomaterials contributes to the design of safe and efficacious nanomedicine. Matter, 6(8), 2564 (2023); https://doi.org/10.1016/j.matt.2023.06.023.

M. Saukani, et al., Effect of Nano-Zirconia Addition on Mechanical Properties of Metakaolin-Based Geopolymer. Journal of Composites Science, 6(10), 293 (2022); https://doi.org/10.3390/jcs6100293.

F.M. Alwan, and H.M. Kamal, Study the effect of addition zirconium oxide ceramic powder on silica-modified geopolymer mortar composite. AIP Conference Proceedings, 3097(1); 060004 (2024); https://doi.org/10.1063/5.0211509.

C. Rahmawati, et al., The Effects of Nanosilica on Mechanical Properties and Fracture Toughness of Geopolymer Cement. Polymers, 13(13), 2178 (2021); https://doi.org/10.3390/polym13132178.

Y. Faza, et al., Synthesis of Porous Metakaolin Geopolymer as Bone Substitute Materials. Key Engineering Materials, 829, 182 (2020); https://doi.org/10.4028/www.scientific.net/KEM.829.182.

A. Harmaji, and B. Sunendar, Utilization of Fly Ash, Red Mud, and Electric Arc Furnace Dust Slag for Geopolymer. Materials Science Forum, 841, 157 (2016); https://doi.org/10.4028/www.scientific.net/MSF.841.157.

D.V. Popov, R.A. Spikings, and T. Razakamanana, Inclusions of Amorphous and Crystalline SiO2 in Minerals from Itrongay (Madagascar) and Other Evidence for the Natural Occurrence of Hydrosilicate Fluids. Geosciences, 12(1), 28 (2022); https://doi.org/10.3390/geosciences12010028.

V. Kumar Yadav, and M.H. Fulekar, Green synthesis and characterization of amorphous silica nanoparticles from fly ash. Materials Today: Proceedings, 18, 4351 (2019); https://doi.org/10.1016/j.matpr.2019.07.395.

S. Ainomugisha, M.J. Matovu, and M. Manga, Influence mechanisms of silica nanoparticles’ property enhancement in cementitious materials and their green synthesis: A critical review. Case Studies in Construction Materials, 20, e03372 (2024); https://doi.org/10.1016/j.cscm.2024.e03372.

X. Song, et al., Thermophysical and mechanical properties of cubic, tetragonal and monoclinic ZrO2. Journal of Materials Research and Technology, 23, 648 (2023); https://doi.org/10.1016/j.jmrt.2023.01.040.

S. Kongkiatkamon, et al., Current classification of zirconia in dentistry: an updated review. PeerJ, 11, e15669 (2023); https://doi.org/10.7717/peerj.15669.

D. Tovar-Vargas, et al., Mechanical properties of ceria-calcia stabilized zirconia ceramics with alumina additions. Journal of the European Ceramic Society, 41(11), 5602 (2021); https://doi.org/10.1016/j.jeurceramsoc.2021.05.006.

W. Jiang, et al., Toughening cemented carbides by phase transformation of zirconia. Materials & Design, 202, 109559 (2021); https://doi.org/10.1016/j.matdes.2021.109559.

S.A. Di Pietro, et al., Solid phase characterization and transformation of illite mineral with gas-phase ammonia treatment. Journal of Hazardous Materials, 424, 127657 (2022); https://doi.org/10.1016/j.jhazmat.2021.127657.

H. Xue, et al., Study of Structural Transformation and Chemical Reactivity of Kaolinite-Based High Ash Slime during Calcination. Minerals, 13(4), 466 (2023); https://doi.org/10.3390/min13040466.

B.P. Bezerra, M.R. Morelli, and A.P. Luz, Effect of reactive silica sources on the properties of Na-metakaolin-based geopolymer binder. Construction and Building Materials, 364, 129989 (2023); https://doi.org/10.1016/j.conbuildmat.2022.129989.

B. Biswas, et al., Understanding Iron Impurities in Australian Kaolin and Their Effect on Acid and Heat Activation Processes of Clay. ACS Omega, 8(6), 5533 (2023); https://doi.org/10.1021/acsomega.2c06795.

L.M. Costa, et al., Influence of the addition of amorphous and crystalline silica on the structural properties of metakaolin-based geopolymers. Applied Clay Science, 215, 106312 (2021); https://doi.org/10.1016/j.clay.2021.106312.

M. Tabish, M.M. Zaheer, and A. Baqi, Effect of nano-silica on mechanical, microstructural and durability properties of cement-based materials: A review. Journal of Building Engineering, 65, 105676 (2023); https://doi.org/10.1016/j.jobe.2022.105676.

F. Zhang, et al., Slow crack growth resistance of electrically conductive zirconia-based composites with non-oxide reinforcements. Journal of the European Ceramic Society, 39(2), 641 (2019); https://doi.org/10.1016/j.jeurceramsoc.2018.09.034.

M.F. Zawrah, R.S. Farag, and M.H. Kohail, Improvement of physical and mechanical properties of geopolymer through addition of zircon. Materials Chemistry and Physics, 217, 90 (2018); https://doi.org/10.1016/j.matchemphys.2018.06.024.

F.W.M. Ling, H.A. Abdulbari, and S.-Y. Chin, Synthesis and characteristics of silica nano-particles using modified sol–gel method in microreactor. Materials Today: Proceedings, 42, 1 (2021); https://doi.org/10.1016/j.matpr.2020.07.563.

M.M. Wetwet, et al., Multifunctional cementitious blends containing zirconia nanoparticles: Mechanical characteristics, gamma attenuation behavior, and self-cleaning performance. Journal of Building Engineering, 65, 105736 (2023); https://doi.org/10.1016/j.jobe.2022.105736.

A.I. Borș, Fourier-Transform Infrared Spectroscopy Analysis of 3D-Printed Dental Resins Reinforced with Yttria-Stabilized Zirconia Nanoparticles. Dentistry Journal, 13(6), 272 (2025); https://doi.org/10.3390/dj13060272.

A.P. Rodrigues, et al., Electron Beam Irradiation on the Production of a Si- and Zr-Based Hybrid Material: A Study by FTIR and WDXRF. Materials (Basel), 16(2), 489 (2023); https://doi.org/10.3390/ma16020489.

L.-L. Kang, et al., Enhancing Resin Cement Adhesion to Zirconia by Oxygen Plasma-Aided Silicatization. Materials, 15(16), 5568 (2022); https://doi.org/10.3390/ma15165568.

C. Cui, et al., Mechanism of zirconia in suppressing cracking during thermal deformation of molybdenum alloys. Journal of Alloys and Compounds, 1047, 185104 (2025); https://doi.org/10.1016/j.jallcom.2025.185104.